Drawing scale calculator

Enter a dimension and a scale to get the other dimension. If you do not know the scale, enter one known dimension and measure it on the printout. Units: mm, cm, m, km, in, ft.

Free, no sign-in

What do you want to calculate?

Result

Real dimension

4 m

Calculation: 40 mm × 100 = 4,000 mm

The same in other units: 4,000 mm · 400 cm · 0.004 km · 157.4803 in · 13.1234 ft

The result is an estimate: the arithmetic is exact, but measuring accuracy depends on the drawing, the printout and how you read it.

Calculations run in your browser. The numbers you type are not sent to a server, and no account is needed.

Common drawing scales

How many millimetres on paper correspond to 1 metre in reality, and how many millimetres in reality correspond to 1 mm on the drawing.

Common drawing scales
Scale1 mm on the drawing =1 m in reality =
1 : 11 mm in reality1,000 mm on paper
1 : 22 mm in reality500 mm on paper
1 : 55 mm in reality200 mm on paper
1 : 1010 mm in reality100 mm on paper
1 : 2020 mm in reality50 mm on paper
1 : 2525 mm in reality40 mm on paper
1 : 5050 mm in reality20 mm on paper
1 : 7575 mm in reality13.33 mm on paper
1 : 100100 mm in reality10 mm on paper
1 : 125125 mm in reality8 mm on paper
1 : 150150 mm in reality6.67 mm on paper
1 : 200200 mm in reality5 mm on paper
1 : 250250 mm in reality4 mm on paper
1 : 500500 mm in reality2 mm on paper

“Fit to page” or printing on a smaller sheet changes the scale. Every A-series sheet has sides in the ratio √2, so one sheet step scales lengths by 0.7071 (or 1.4142 when enlarging).

A printout that is not to scale: sheet changes A0–A4
Sheet changeLength factorA 1:50 label behaves likeA 1:100 label behaves like
A3 → A4× 0.70711 : 70.71 : 141.4
A2 → A4× 0.51 : 1001 : 200
A1 → A4× 0.35361 : 141.41 : 282.8
A0 → A4× 0.251 : 2001 : 400
A4 → A3× 1.41421 : 35.41 : 70.7
A4 → A2× 21 : 251 : 50

The factors come from the ISO 216 proportions (A3 = 297 × 420 mm, A4 = 210 × 297 mm). A real printout also depends on printer margins, so always check the scale with a ruler on a known dimension or with the “Find the scale” mode.

ISO 216 sheet sizes

FormatSize (mm)
A0841 × 1189
A1594 × 841
A2420 × 594
A3297 × 420
A4210 × 297

How to convert a drawing dimension

  1. Find the scale

    Read the scale from the title block or the scale bar (e.g. 1:100). If there is none, work it out from one known dimension with the “Find the scale” mode.

  2. Measure the dimension on the drawing

    Measure the segment with a ruler on the printout or in the file. Enter the result in the units you measured it in.

  3. Choose the scale and the result unit

    Pick the scale from the list or enter your own denominator. The calculator multiplies the dimension by N for a 1:N scale.

  4. Check that the printout is to scale

    Compare a known dimension on the printout with its real value. If they differ, the printout has been rescaled.

Formulas

  • Real dimension = drawing dimension × N (for a 1:N scale)
  • Drawing dimension = real dimension ÷ N
  • N = real dimension ÷ dimension measured on the printout
  • Format change: A3 → A4 factor = 297 ÷ 420 = 0.7071; scale after reduction = 1:(N ÷ 0.7071)
  • Units: 1 in = 25.4 mm, 1 ft = 12 in = 304.8 mm

Frequently asked questions

How do I get the real dimension from a 1:100 scale?
Multiply the dimension measured on the drawing by 100. A 40 mm segment on a 1:100 drawing means 4000 mm, that is 4 m.
How many millimetres on the drawing is 1 metre at 1:50?
20 mm, because 1000 mm ÷ 50 = 20 mm. At 1:100 it is 10 mm and at 1:20 it is 50 mm. See the table of scales for all values.
Why does a dimension on my printout not match the scale?
Most often the printout has been reduced or enlarged: by “fit to page”, a different paper size or a copier. An A3 drawing printed on A4 is 0.707 of the original size, so a 1:50 label then behaves like about 1:70.7. Check it with the “Find the scale” mode.
Does the calculator support inches and feet?
Yes. 1 inch is 25.4 mm and 1 foot is 304.8 mm. Enter a dimension in mm, cm, m, km, in or ft and choose the result unit. A 1/4″ = 1′ scale is 1:48, so enter 48 as a custom denominator.
Is the result accurate?
Arithmetically yes, but accuracy depends on measuring the drawing. A reading error of 0.5 mm on paper at 1:100 is already 50 mm in reality; estimate it with the reading-error calculator.

Guides

Other tools

Measure on the whole drawing instead

The calculator handles a single dimension. In the Skalnivo app you open a file (PDF, DWG, DXF, photo), calibrate the scale with one known dimension and measure distances and areas directly on the drawing, without converting by hand.