Glossary of drawing and measuring terms

Short definitions of terms that come up when measuring on drawings. Each entry has its own address with an anchor, and the first sentence is the definition.

Drawing scale
Drawing scale is the ratio of a length on the drawing to the corresponding length in reality. A notation of 1:100 means 1 mm on the drawing is 100 mm in reality. It applies to the original sheet; once a printout is reduced or enlarged it no longer holds. See How to read a drawing scale.
Calibration
Calibration is setting the scale of a document by picking two points on a segment of known length and entering that length. In Skalnivo it is stored separately for each page or scan, and on a sheet with several scales also for a chosen area; it can be checked with a second known dimension. See Your first calibration.
Calibration segment
A calibration segment is a part of a drawing with a known length, on which calibration is set. The longer and more clearly labelled it is, the smaller the relative error of later measurements.
Scale factor
The scale factor is the number of real-world units per one document unit, calculated as the known length divided by the distance between the calibration points. Every measured distance is multiplied by it.
Dimension
A dimension is the length of an element on a drawing, labelled with a number, usually with a dimension line and ticks or arrows at the ends. It is the basis of calibration, provided the label is correct.
Chain dimensions
Chain dimensions are a series of partial dimensions laid out one after another along the same line. The sum of the partial dimensions may differ from the overall dimension because of rounding.
Sheet size
Sheet size is the standardised paper size of a drawing from the A series: A0 is 841 × 1189 mm (33.1 × 46.8 in), A1 594 × 841 mm, A2 420 × 594 mm, A3 297 × 420 mm, A4 210 × 297 mm (8.3 × 11.7 in). It lets you judge whether a PDF has kept the size of the original.
Floor plan
A floor plan is a drawing of an object seen from above after cutting it with a horizontal plane, for example the layout of rooms on a floor. Distances and areas are most often read from a floor plan.
Elevation
An elevation is a drawing of an external wall of a building seen from the side, without perspective. It is used to read heights and the positions of windows and doors.
Section
A section is a drawing of an object cut by a vertical plane, showing its interior, layer thicknesses and heights. It has its own scale, often different from the floor plan.
Detail
A detail is an enlarged drawing of part of an object, for example a junction between elements. It is usually at a larger scale than the main drawing, and one sheet may hold several details at different scales.
Model space
Model space is the area of a CAD file in which the geometry of the object is drawn in real-world units. Skalnivo draws model space. See A DWG file on your phone.
Layout (paper space)
A layout is, in a CAD file, a sheet prepared for printing with views of model space at a chosen scale. Skalnivo does not draw layouts; it shows a warning.
DWG
DWG is a binary drawing file format of CAD programs, storing geometry, layers, blocks and dimensions. Skalnivo reads versions R14 to R2018. See the DWG format.
DXF
DXF is a CAD drawing exchange format with a documented structure, saved as text or binary data. Skalnivo reads versions R12 to R2018. See the DXF format.
Vector PDF
A vector PDF is a PDF document in which lines and text are stored as coordinates and curves, so they stay sharp when zoomed in. See measuring on a PDF.
Raster PDF (from a scan)
A raster PDF is a PDF document containing an image made of pixels, for example a scanned drawing. Its accuracy is limited by the resolution and distortion of the scan.
Perspective correction (homography)
Perspective correction is the transformation of a photo of a flat sheet taken at an angle into a rectangle based on four corners, known mathematically as a homography. It does not know real lengths, so calibration is needed afterwards. See scanning drawings.
External reference (xref)
An external reference (xref) is the attachment of one CAD drawing to another as a reference, without copying the geometry. Skalnivo detects an xref but does not load it, and warns that part of the drawing is missing.
Layer
A layer is a group of elements in a CAD file with shared properties that can be switched on or off, for example walls, dimensions or services. In Skalnivo, layer visibility changes only in the view.
Block
A block is a named set of CAD elements that can be inserted many times, for example a window symbol. Skalnivo reads blocks, including nested and scaled ones.
Drawing units
Drawing units are the unit of length in which the coordinates of a CAD file are stored, for example millimetres or metres. When they are recorded, dimensions can be read without manual calibration; when they are missing, calibration is needed.
Snapping
Snapping is the automatic placing of a point on a reliable element of the drawing, such as the end of a line or the centre of a circle. In Skalnivo it covers measurement points, PDF vectors (in the mobile app) and DWG/DXF geometry, and it can be switched off in Profile.
Polyline
A polyline is a series of segments joined end to end. The Polyline length tool adds up their lengths, which is useful for measuring runs of pipe, duct and cable.
Polygon area
Polygon area is the surface of the region bounded by a closed polyline. Skalnivo calculates it with the shoelace formula and flags self-intersecting polygons with a warning.
Perimeter
Perimeter is the sum of the side lengths of a closed polygon, or the circumference of a circle. In Skalnivo the Perimeter tool does this.
EXIF
EXIF is metadata stored in a photo, including the orientation of the image. Skalnivo uses it to rotate the image correctly, but not to determine the scale.
Resolution (DPI)
Resolution in DPI is the number of pixels per inch of an image. It does not describe a real length on the drawing, so the scale is not derived from DPI but from calibration.
Relative error
Relative error is the difference between a result and a reference value divided by the reference value, usually as a percentage. With calibration it falls as the calibration segment gets longer. See Accuracy and methodology.

Updated: